|
 |
|
|
2.5" Grip Head (or Hollywood or Gobo Head) |
day-rate |
features:
o attaches to Baby pins, boom arms, and steel rods
o holds Baby pins, boom arms, and steel rods, foam core, etc.
grip tips:
right-hand rule
- When securing a load in a grip head, turn the head clutch handle towards
you and tighten with the load to the right. The weight will naturally
tighten rather than loosen the grip head. |
|
 |
|
|
#1, #2, #3 Grip Clip
(Pony Clamp) |
day-rate |
The most common
clamp used in the motion picture business. Three sizes to suit your
every needs.
features:
Um...it's a clamp! :-)
|
|
|
 |
|
features:
o clamps to pipes, 2x4's
o 5/8" to 2.5'' on
round stock, 0" to 3" on flat
o grip pads hold tight
o baby pin |
|
 |
|
|
Super Mafer clamp with Baby pin |
day-rate |
features:
o clamps to pipes, 2x4's, anything from 3/4" to
2 1/4" thick
o removable baby pin provides mounting point for light
o soft rubber grips prevent
marring of surfaces
grip tips:
o clamp to a Bogen Autopole to add a
light anywhere
o clamp two to a light stand
to hang two lights
o clamp to the top of a set wall or any wood beam
o connect two together to clamp two pipes togetheR |
|
|
 |
|
|
Super Mafer clamp
swivel snap-in pin |
day-rate |
features:
o interconnects two Super Mafer clamps
grip tips:
o use with two Mafer clamps to connect Bogen Autopoles
or any structural member |
|
|
 |
|
|
Baby Pin with 3/8"-16 threaded hole |
day-rate |
features:
o bolts onto suction cups and camera plates to
provide mounting point for grip heads |
|
|
 |
|
|
Baby Starter Pin with 3/8"-16 thread
thru-hole |
day-rate |
features:
o bolts onto suction cups and camera plates to
provide mounting point for grip heads
o shorter pin for tighter spaces
o 3/8" thread runs through the pin for mounting on both sides |
|
 |
|
|
Drop-ceiling scissor clamp with
Baby pin |
day-rate |
features:
o clamps to the T-frame of a typical
drop-ceiling
o baby pin
grip tips:
o don't hang anything heavier than a
Baby on this
or you risk collapsing the ceiling. |
|
 |
|
features:
o provides mounting point for Baby hardware
o secure to floors, set walls, apple boxes
o 3" version available
|
|
|
 |
|
Baby Pin to 1/4"-20 threaded bolt
(camera
starter) |
day-rate |
features:
o connects lightweight cameras
to baby hardware
o use in camera's base to mount a camera in odd places
o use in camera's top handle to provide a grip point |
|
 |
|
features:
o connects mounting points together to create
frames
o 6", 9", 12", 24" available |
|
 |
|
features:
o use to secure grip rigs to vehicles
o use to secure gear in trucks |
|
 |
|
|
Modern Studio Mini Ball
Camera Plate |
day-rate |
features:
o swappable plates support 1/4" and 3/8" camera
threads
o one tightening knob provides quick fine tuning of tilt and position
o rotation of plate provides 6" of horizontal positioning freedom
o cheese plate with 3/8" holes for mounting of other hardware
o 25lb capacity - 60lb's when top of camera is supported |
|
 |
|
6" Suction Cup with 3/8"-16 male thread
(shown with baby pin attached) |
day-rate |
features:
o 70 pound capacity
o simple plunger evacuates the air inside cup
o red-line indicator warns if there is any drop in holding power
o instant removal with a slight pull on an edge tab
|
  |
